
Micromotor handpiece · EQ.14.01
Long hours of fine pavé tire your hand, and a heavy, vibrating handpiece makes it worse. The JURA Slim Fit is our lightest and shortest handpiece. Its slim, ergonomic nose feels like a pen in your hand, it runs silent and without vibration, and you keep a clear view of the stone. Less strain on your hand, more control, for the finest pavé work hour after hour. Designed for delicate work with ball burs up to Ø1.8 mm, not for polishing or low-quality mandrels.
E-Type: change handpieces in seconds on the same motor, no separate micromotor needed. Standard with the Graver Plus and Graver PRO, for the JURA Micromotor, and fits most E-Type micromotors.
New to a micromotor system? Choose the JURA by NSK Slim Fit Pavé (EQ.14.02): the same slim fit and ergonomic handling, with extra durability.
Your micromotor system
All accessories are sold separately.
Standard with Graver Plus & PRO
EQ.14.01 · E-Type micromotor handpiece
Best for
Fine pavé with small stones, ball burs up to Ø1.8 mm, and drills and burs that must run perfectly centred.
Good to know
Our lightest and shortest handpiece: feels like a pen in your hand. Silent, no vibration. NOT for polishing, large burs or low-quality mandrels. New to a micromotor system? Choose the EQ.14.02.
Essential
the full range · not included, sold separately
Every drill and bur you need for setting, in one category.
Choose the sizes for your stones; ball burs up to Ø1.8 mm in this handpiece.
Essential
not included, sold separately
Cooler, cleaner cutting, a longer life for every drill and bur, and less wear on your handpiece.
A touch on the tip before you start.
Essential
Lance · 0.3 mm tip · not included, sold separately
For the finest pavé work: open and clean the smallest seats with control.
The precision of the Slim Fit at its best.
Other micromotor handpieces
EQ.14.02
The same slim fit, with extra durability. Recommended if you are new to a micromotor system or used to a flex-shaft motor.
The Slim Fit is not meant for polishing. For polishing, choose the JURA by NSK Heavy Duty (EQ.14.03). Our heaviest handpiece, with an independently adjustable chuck: very suitable for polishing wheels and mandrels, and for large burs from Ø2 mm.
What you gain
Feels like a pen
The slim, ergonomic nose rests naturally in your fingers.
Less strain on your hand
Our lightest and shortest handpiece: comfortable through long hours of fine pavé.
Silent, no vibration
Calm, steady work and a clear view of the stone.
Change in seconds
E-Type: switch to another JURA handpiece on the same motor, no separate micromotor needed.
Ready from day one
Standard with the Graver Plus and Graver PRO.
For the finest work
Pair it with ultra-fine diamond burs for the smallest stones.
Recommended speeds
On a phone, swipe the table sideways to see all columns.
| Bur type | Speed |
|---|---|
| Drills and ball burs
|
3,000 – 4,000 rpm |
| Cylinders and tapered burs
|
5,000 – 6,000 rpm |
Important usage note. A JURA E-Type micromotor is not a flex-shaft motor: it is a delicate, precision system. Always build up ball bur sizes gradually, from small to large, to keep full control and get fine results, and use lubricant. Avoid cheap ball burs and mandrels, especially mandrels: they can damage the bearings and shorten the life of your handpiece.
Disclaimer
The JURA Slim Fit is NOT meant for polishing, and NOT for low-quality burs or mandrels. The handpiece comes with a 1-year warranty. Polishing, large or low-quality burs and mandrels, and working without lubricant each leave their own recognisable wear in the handpiece; this wear is not covered by the warranty.
Specifications
On a phone, swipe the table sideways to see all columns.
| Specification | JURA Slim Fit |
|---|---|
| SKU
|
EQ.14.01 |
| Type
|
E-Type micromotor handpiece |
| Burs
|
Ball burs up to Ø1.8 mm |
| Not for
|
Polishing, large burs and low-quality mandrels |
| Standard with
|
Graver Plus and Graver PRO |
| Weight and size
|
Our lightest and shortest handpiece |
| Speeds
|
Drills and ball burs 3,000 – 4,000 rpm; cylinders and tapered burs 5,000 – 6,000 rpm |
| Compatibility
|
JURA Micromotor, Graver Plus and Graver PRO; fits most E-Type micromotors |
| Warranty
|
1 year |
Personal advice
Not sure which handpiece suits your work? Tell us what you set, and we will help you choose.
All prices exclude VAT. Final VAT and shipping are applied at checkout based on your region and VAT registration status.