

HS code 8205 70 00 · US HTS 8205.70.00.90
New · set of 15 · Ø15–22 mm
Change collets in seconds. Changing collets means stopping, loosening and fiddling, again and again during the day. These brass collets are reengineered: release and change them from one side in seconds, and get straight back to setting.
In the box
15 Brass Collets Quick Release, Ø15–22 mmRadius dividerQuick Release CylinderNew screw set for the Horizontal Ring Holder
SKU MH.11.M.QR
Good to know
Compatible with the JURA Classic Quick Change ring fixtures, such as the Horizontal Ring Holder (QC.10), and the JURA 3X Line
Made for work on the side of the ring: French cut and multiple-side setting. The steps on the sides fix the ring firmly in that position.
Centre work is possible too. Setters who use it with the ring in the centre usually do so for hammering, because the brass collet absorbs the vibration. In the centre the collet expands much harder, so for other centre work we prefer the High Performance collets ourselves.
New collets are stiff at first and become more flexible with use. Tighten the ring with two hex keys turned against each other.
Always choose the correct collet size: a collet that is too small for the ring can break.
Radius divider included; a spare or extra set: the Radius Ring Divider + Screw (SP.RD)
Need an extra screw set? The Quick Collet Screw Set (SP.QC.11)
The screw set is only needed to use these collets on your existing Horizontal Ring Holder – on the JURA 3X Line you do not need it. On the Horizontal Ring Holder, shorten the screw by 4 mm with the Diamond Cutting Wheel (PL.CW), so you can fix the collet with two hex keys from both sides
On the JURA Collets Organizer (OZ.17) these collets sit a little loose on the pins: slide a short piece of silicone tube (from any hardware store) over each pin and they sit firmly
The photo shows 12 collets; the set contains 15
At the bench
Quick release
Release and change the collets from one side in seconds, for a faster workflow.
Made for hammering
Robust brass that withstands even the most vigorous hammering.
Layout and steps
The radius divider makes layout on the side of rings effortless; steps on the sides support fishtail and multi-sided settings on micro bands.
Which one do you need?
High Performance · MH.11.HP
Set of 10, high-temperature polymer
Stable up to 250 °C: for heavy drilling and burring
Uses the standard screw set: Spare Horizontal Ring Holder Screw Set (SP.QC.10)
Brass Classic · MH.11.M
Set of 15, Ø15–22 mm
For the most vigorous hammering
Radius divider and screw included
Uses the standard screw set: Spare Horizontal Ring Holder Screw Set (SP.QC.10)
Brass Quick Release · MH.11.M.QR · this page
Set of 15 brass collets, Ø15–22 mm
Released and changed from one side in seconds
Includes the new screw set for the Horizontal Ring Holder; extra set: Quick Collet Screw Set (SP.QC.11)
In six 3X sets
Want to know how JURA tools add real value to your business?
Take it to the next level
The radius divider, the holder, an extra screw set, and the classic brass collets.
Marks every line on the side of the ring from one centre point: made for fishtail setting. For both brass collet sets.
€27 excl. VAT
See details
QC.10
The clamp diamond setters use most: two-sided clamping, turning the ring all the way around.
€162 excl. VAT
See details
SP.QC.11
An extra screw set for the Brass Collets Quick Release, with an extended thread for a secure hold.
€44 excl. VAT
See details
MH.11.M
Set of 15, Ø15–22 mm, built for the most vigorous hammering, with a radius divider and screw.
€190 excl. VAT
See detailsExplore more
Personal advice
Not sure which clamp suits your work? Tell us what you set or engrave, and we will advise you.
Photos are an indication: we keep developing our products, so details may differ slightly.
All prices exclude VAT. Final VAT and shipping are applied at checkout based on your region and VAT registration status.